- 12V LiFePO4 20A charger [ 12V LiFeP04 20A charger id: 451 qty: 1]:67.49
- 12V LiFePO4 20Ah battery [ 12V Lithium battery id: 447 qty: 1]:46.99
- 12V switch bank-Six push button switches for daytime running lights, old school headlight switch and 12V on/off breaker. Allows for expansion of fuse box to be mounted below switch bank. 160mm x 80mm face size, top and bottom size [ id: 436 qty: 1]
- 1in Keyhole for volt meter [ 1" keyhole id: 492 qty: 3]:6.75
- 18/8 Controller power from controller junction box to switch bank [ 18/8 wire id: 480 qty: 500]:1.42
- 2 Port WAGO - All 12V switches - 7 x 3. 21 total [ 2 Port WAGO id: 479 qty: 21]:10.13
- Profile. 2080. Top is like dash, 160mm. Same as bottom. Sides are short, 80mm. 480mmm total [ 2080 Black id: 437 qty: 480]:9.6
- HDPE. 160mm x 120mm face and back [ HDPE Sheet 4' x 8' x .25" thick id: 438 qty: 0.13]:8.28
- M12 access holes for push button switches and gland in back [ M12 access hole id: 443 qty: 7]:15.75
- Push button switches: six for the running lights; one for 12V on/off [ M12 push button threaded switch id: 477 qty: 7]:18.13
- M5 x 8mm [ M5 TNut id: 432 qty: 32]:1.12
- M5 x 8mm [ M5 TNut id: 439 qty: 32]:1.12
- M6 access holes [ M6 access hole id: 433 qty: 18]:40.5
- M6 access holes [ M6 access hole id: 440 qty: 11]:24.75
- M6 mounting holes [ M6 access hole id: 444 qty: 18]:40.5
- M6 mounting holes [ M6 access hole id: 445 qty: 12]:27
- M6 TNut [ M6 TNut id: 435 qty: 4]:0.72
- M6 TNut [ M6 TNut id: 442 qty: 4]:0.72
- M6 x 10mm [ M6 x 10mm id: 434 qty: 4]:0.64
- M6 x 10mm [ M6 x 10mm id: 441 qty: 4]:0.64
- Gland for 12V switch bank [ P9 Gland id: 446 qty: 1]:0.22
- Glands for instrument panel [ P9 Gland id: 506 qty: 3]:0.67
- Prep wire for 18/8 controller to switch bank run [ Strip, Crimp, insulate wire end id: 485 qty: 8]:4.64
- Volt Meter - 12V [ Volt meter id: 474 qty: 1]:2.66
- 12/2 wire [ 14/2 wire id: 448 qty: 1080]:2.83
- 18/2 Wire from switch bank to junction box; junction box to each LED Strip [ 18/2 wire id: 469 qty: 6000]:5.9
- 18/2 Wire from 12V junction to front blinkers [ 18/2 wire id: 488 qty: 2000]:1.97
- 18/2 Wire from 12V junction to horn [ 18/2 wire id: 496 qty: 1000]:0.98
- 18/8 Wire from 12V front juntion to rear [ 18/8 wire id: 460 qty: 2500]:7.1
- 18/8 Wire from rear to roof LED bar [ 18/8 wire id: 466 qty: 2000]:5.68
- 18/8 Wire from rear junction box to LP module [ 18/8 wire id: 472 qty: 500]:1.42
- 2 Port WAGO [ 2 Port WAGO id: 461 qty: 11]:5.31
- 2 Port WAGO [ 2 Port WAGO id: 464 qty: 3]:1.45
- 2 Port WAGO connect to LED strip [ 2 Port WAGO id: 467 qty: 48]:23.16
- 2 Port WAGO connect to LP module [ 2 Port WAGO id: 470 qty: 5]:2.41
- 2 Port WAGO - front blinkers [rear blinkers covered by LED strip line items] [ 2 Port WAGO id: 489 qty: 12]:5.79
- Ring terminals [ 22 AWG ring terminal id: 449 qty: 2]:0.3
- 5 Port WAGO [ 5 Port WAGO id: 458 qty: 11]:6.81
- Andersen connector [ Anderson Connector - AWG 12 - 10 id: 450 qty: 1]:1.7
- Blinker module [ Blinker Module id: 457 qty: 2]:5
- Cable Blocks for run to rear [ Cable Mounting Block id: 462 qty: 5]:0.65
- Cable Blocks for run from rear to roof LED bar [ Cable Mounting Block id: 465 qty: 3]:0.39
- Horn [ Horn id: 494 qty: 1]:15
- Inline Fuse [ In line pigtail + fuse id: 459 qty: 10]:7.5
- Inline Fuse LP Module [ In line pigtail + fuse id: 473 qty: 1]:0.75
- Inline Fuse 12V battery [ In line pigtail + fuse id: 478 qty: 1]:0.75
- LED Bar [ LED Bar id: 463 qty: 2]:56.08
- LED Strip - 8 amber, 8 red, 8 white [ LED Strips: red, white or amber id: 468 qty: 24]:82.14
- LP Module [ LP Module id: 471 qty: 1]:12.98
- M8 nylon mounting bolts [ M8 x 14mm nylon bolt id: 453 qty: 4]:2.8
- Odometer and GPS Speedometer [ Odometer and Speedometer id: 532 qty: 1]:62.99
- Prep wire for 18/8 rear 12V run [ Strip, Crimp, insulate wire end id: 483 qty: 8]:4.64
- Prep wire for 18/8 rear to roof run [ Strip, Crimp, insulate wire end id: 484 qty: 8]:4.64
- Prep wire for 18/8 rear to LP Module [ Strip, Crimp, insulate wire end id: 486 qty: 5]:2.9
- Prep wire for 18/2 LED Strips [ Strip, Crimp, insulate wire end id: 487 qty: 24]:13.92
- Prep wire for 18/2 blinkers [ Strip, Crimp, insulate wire end id: 490 qty: 2]:1.16
- Prep wire for horn [ Strip, Crimp, insulate wire end id: 495 qty: 5]:2.9
- TNut [ T Nut slide in id: 454 qty: 4]:0.4
- 12V Waterproof junction box [ Waterproof Container: Large id: 452 qty: 1]:5.2
- 18/8 Rear Controller signal wires [ 18/8 wire id: 401 qty: 2000]:5.68
- 4 AWG Wire. 25 feet of black and 25 feet of red [ 4 AWG id: 399 qty: 1]:0.03
- 4 AWG Lugs [ 4 AWG Lugs id: 400 qty: 24]:23.98
- 72V instrument panel-BMS display, BMS on/off [button comes with display] [ id: 498 qty: 1]
- Profile. 2080. Bottom is the dash [i.e. nothing to add]. Top, back and face are paneling. Sides cut on 45 degree angle, Sunshade is 2080. [ 2080 Black id: 499 qty: 480]:9.6
- HDPE. 160mm x 120mm face and back [ HDPE Sheet 4' x 8' x .25" thick id: 500 qty: 0.13]:8.28
- Jigsaw hole for BMS display [ Jig Saw hole id: 497 qty: 1]:4
- Jigsaw hole for odometer [ Jig Saw hole id: 533 qty: 1]:4
- M12 access holes for glands and push button switch [ M12 access hole id: 505 qty: 4]:9
- M5 x 8mm [ M5 TNut id: 501 qty: 8]:0.28
- Thread sides [ M6 access hole id: 502 qty: 8]:18
- M6 TNut [ M6 TNut id: 504 qty: 4]:0.72
- M6 x 10mm [ M6 x 10mm id: 503 qty: 8]:1.28
- 72V Power Management Board-Breaker x 3 for each controller; 300A 72V DC fuse; GND terminal block [ id: 393 qty: 1]
- 10k ohm resistor [ 10kW resistor id: 395 qty: 1]:0.7
- Fuse Block [ 300A ANL Fuse and Holder id: 397 qty: 1]:8
- GND Distribution Block [ 4 post GND distribution block id: 398 qty: 1]:17.99
- Breaker [ 72V DC 150A Breaker id: 394 qty: 3]:60.9
- Prep wire for +V to/from ANL [x4], GND to/from distribution [x4], +V from breaker to controller [x3]. Both sides: 22 [ Strip, Crimp, insulate wire end id: 420 qty: 22]:12.76
- Prep resistor , both ends [ Strip, Crimp, insulate wire end id: 424 qty: 2]:1.16
- LiFeP04 Battery System-Prismatic Cells, BMS [with balance wires and display], ring terminals, B+, P+, B-, P-, C+, C- [ id: 402 qty: 1]
- Duct Tape. Used to wrap 4 blockers. Each 4 blocker needs about 1200mm [ 10in Duct Tape id: 428 qty: 4800]:5.05
- 22AWG ring terminals [ 22 AWG ring terminal id: 404 qty: 24]:2.8
- Battery Case [ 24S Battery Case id: 406 qty: 1]:190.9
- Prismatic Cells [ 3.2V 280Ah Prismatic Cell id: 403 qty: 24]:1439.94
- Anderson connector. Charging and power [ Anderson Connector - heavy gauge wire id: 419 qty: 2]:6
- BMS [ BMS 24S id: 405 qty: 1]:171.03
- Cut Foam for battery case [ Cut Foam id: 425 qty: 26]:4.16
- Glands for battery case. One for each heavy gauge wire [x4]. One for display and ancillary 22-12 AWG wires. 5 total [ P9 Gland id: 427 qty: 5]:1.12
- PVC sheet. One between each cell in a 4 block of cells [3 x 6] and one between each section of 4 blockers [x5]. One below and above the BMS 25 total [ PVC Sheet id: 426 qty: 25]:38.5
- Prep wire for B- [x2], P-, C-, B+, C+ - six total prep tasks, both ends - 12 total. [ Strip, Crimp, insulate wire end id: 418 qty: 12]:6.96
- 2 Hole Brackets brake pedal [ 45 Series Corner Bracket - 2 Holes id: 513 qty: 2]:8.84
- Brake Caliper [ Brake caliper id: 507 qty: 3]:18.99
- Front Brake Line right side, 1200mm [ Brake Line, 120cm id: 509 qty: 1]:8.99
- Rear Brake Line right side, 2300mm [ Brake Line, 230cm id: 517 qty: 1]:18.49
- Front Brake Line left side, 500mm [ Brake Line, 50cm id: 508 qty: 1]:9.99
- Brake Master Cylinder [ Brake Master Cylinder id: 510 qty: 1]:48.99
- Brake Pedal [ Brake Pedal id: 511 qty: 2]:90.54
- Brake Push Rod [ Brake Pedal push rod id: 512 qty: 1]:19.99
- Cable Block for rear Brake line and 3 phase [ Cable Mounting Block id: 518 qty: 4]:0.52
- M10 hole for brake pedal [ M10 access hole id: 516 qty: 2]:4.5
- M8 x 16mm [ M8 x 16mm id: 514 qty: 2]:0.31
- TNuts [ T Nut slide in id: 515 qty: 2]:0.2
- Brake System Mounting-The new hood supports act as the forward to rearward supports. The remaining three profiles as as-is: 4590 for master cylinder that mounts to a vert [though shorter by 45 due to the new hood supports] and brake pedal mount that connects between the hood supports [ id: 180 qty: 1]
- Brake Master Cylinder Support-Short 4590 to which the master cylinder mounts. [ id: 189 qty: 1]
- 1.75in key hole for push rod access [ 1.75" keyhole id: 193 qty: 1]:2.25
- Profile [ 45 x 90 Heavy id: 190 qty: 405]:12.4
- QC connector [ Central Connector Circular id: 192 qty: 4]:2.48
- 17mm. [ M17 access hole id: 191 qty: 4]:9
- Brake Pedal Support-Cross bar between the hood supports to which brackets attach that support the brake pedal [ id: 185 qty: 1]
- Profile [ 45 x 90 Heavy id: 186 qty: 405]:12.4
- QC connector [ Central Connector Circular id: 188 qty: 4]:2.48
- 17mm. [ M17 access hole id: 187 qty: 4]:9
- Brake Vertical Support-Using the less expensive and stronger 4590, the vert will mount forward to rearward which might give future mounting options of motors for steering [ id: 181 qty: 1]
- Profile [ 45 x 90 Heavy id: 182 qty: 405]:12.4
- QC connector [ Central Connector Circular id: 184 qty: 4]:2.48
- 17mm. [ M17 access hole id: 183 qty: 4]:9
- Deflector-The angled portion of the front of Evie. This portion connects to the floor or Mustang 2 cross bar. This will most likely contain many more sub-modules in a wheel arch front suspension [ id: 158 qty: 1]
- 45 Support Connectors [ 45°Support Connector 45B id: 164 qty: 2]:12.22
- Angled Sides-Gnarly looking 45 degree supports on the outside of the deflector shield [ id: 166 qty: 2]
- Profile [ 45 x 90 Heavy id: 160 qty: 180]:5.51
- M8 bolt [ M8 x 16mm id: 163 qty: 2]:0.15
- Thread end for 45 support connector [ Thread M12 id: 161 qty: 2]:4.5
- Threaded inserts [ Threaded Insert id: 162 qty: 2]:2.88
- Deflector 45 Deg Base-45 Deg running the length of the front suspension cross bar [ id: 168 qty: 1]
- Profile [ 45 x 45 x 45 Degree id: 159 qty: 630]:21.42
- Deflector 45 Deg Hood-Connect deflector angled [x2] and straights [x2] to the hood frame [ id: 173 qty: 1]
- Profile [ 45 x 45 x 45 Degree id: 174 qty: 1215]:41.3
- Deflector Straights-Inner profiles that give the deflector rigidity [ id: 169 qty: 2]
- Profile [ 45 x 90 Heavy id: 170 qty: 180]:5.51
- QC connector [ Central Connector Circular id: 172 qty: 4]:2.48
- 17mm [ M17 access hole id: 171 qty: 4]:9
- M8 bolt [ M8 x 16mm id: 167 qty: 2]:0.15
- T Nut [ T Nut slide in id: 165 qty: 2]:0.2
- Dual Wheel Floor - Single Side-Floor of front of tadpole trike or four-wheel vehicle - one side. Left and right sides of this module are mirror images, thus quantity of two for this but not its siblings [ id: 18 qty: 2]
- Control Arm Base Mount-Main profile to which the lower control arm L plates and upper control arm mount attach [ id: 20 qty: 1]
- Profile [ 45 x 180 Heavy id: 29 qty: 225]:42.98
- QC connectors [ Central Connector Circular id: 33 qty: 2]:1.24
- Mounting plate for LCA [ Corner Plate 135mm x 135mm angled id: 31 qty: 2]:23.46
- Drill out to 10mm for swing arm bolt [ M10 access hole id: 32 qty: 1]:2.25
- 17mm holes [ M17 access hole id: 30 qty: 2]:4.5
- M8 bolts [ M8 x 16mm id: 34 qty: 3]:0.23
- slide in t nut [ Slide in T Nut id: 35 qty: 3]:1.61
- Upper Control Arm Mount-Profile to which the upper control arm brackets attach [ id: 21 qty: 1]
- Brackets to which the upper control arm mounts [ 45 Series Corner Bracket - 4 Holes id: 46 qty: 2]:16.6
- Profile [ 45 x 90 x 90 id: 134 qty: 180]:19.68
- QC connectors [ Central Connector Circular id: 136 qty: 4]:2.48
- M10 hole for swing arm bolt [ M10 access hole id: 47 qty: 1]:2.25
- 17mm hole - Four total into the Control Arm Base Mount: two in each longitudinal slot [ M17 access hole id: 135 qty: 4]:9
- M8 bolts [ M8 x 16mm id: 48 qty: 3]:0.23
- slide in t nut [ Slide in T Nut id: 49 qty: 3]:1.61
- Control Arm Base Mount Forward Support-Added support to control arm base mount as well as the bumper tee. Sandwiched between both [ id: 19 qty: 1]
- Profile [ 45 x 90 Heavy id: 26 qty: 180]:5.51
- QC connectors [ Central Connector Circular id: 28 qty: 4]:2.48
- 17mm hole [ M17 access hole id: 27 qty: 4]:9
- Control Arm Base Mount Rearward Support-Added support to control arm base mount as well as the rearward wheel arch base mount Sandwiched between both [ id: 22 qty: 1]
- Profile [ 45 x 90 Heavy id: 36 qty: 180]:5.51
- QC connectors [ Central Connector Circular id: 38 qty: 4]:2.48
- 17mm hole [ M17 access hole id: 37 qty: 4]:9
- Foot Rest Forward-On the driver's side, allow steering rack mount,
and brake pedal mount and throttle mount. On passenger's side, just the floor [ id: 23 qty: 1]
- Profile [ 45 x 90 Heavy id: 39 qty: 450]:13.78
- QC connectors [ Central Connector Circular id: 41 qty: 2]:1.24
- 17mm hole [ M17 access hole id: 40 qty: 2]:4.5
- Foot Rest Rearward-One of two profiles to make up the foot rest floor [ id: 25 qty: 1]
- Profile [ 45 x 45 Heavy id: 42 qty: 450]:15.67
- QC connectors [ Central Connector Circular id: 44 qty: 1]:0.62
- 10mm hole to connect foot rest forward to footrest reardward before attaching to backbone [ M10 access hole id: 45 qty: 2]:4.5
- 17mm hole [ M17 access hole id: 43 qty: 1]:2.25
- Floor-All the tslot parts that are critical to making this thing work. Does NOT include dash, front hoop, main hoop, roof, brake or steering supports, swing arms, control arms, seat mounts or switch mounts. Includes everything else, including wheel arches, [ id: 10 qty: 1]
- Backbone-Main strength of the chassis. Runs the entire length of Evie from forward tee to rear tee or rear swing arm [ id: 12 qty: 1]
- 4 hole brackets. Battery Case [ 40 Series Corner Bracket - 4 Holes id: 407 qty: 4]:28.8
- profile [ 45 x 180 Heavy id: 50 qty: 1980]:378.2
- QC connectors [ Central Connector Circular id: 15 qty: 2]:1.24
- 17mm holes [ M17 access hole id: 14 qty: 2]:4.5
- M8 x 16mm bolt [ M8 x 16mm id: 422 qty: 2]:0.31
- TNut [ T Nut slide in id: 423 qty: 2]:0.2
- Bumper Tee-Long cross member that supports forward wheel arches, the bumper and front crumple zone. Attaches to end of backbone via 2 QC connectors [ id: 11 qty: 1]
- 4545 tslot [ 45 x 45 Heavy id: 13 qty: 1260]:43.88
- end caps [ End Cap 45mm x 45mm id: 16 qty: 2]:3.36
- Passenger Floor-Standard floor starting with profiles that attach to the 45 Degs in front with new mirror image of it in the rear to accept either swing arm single wheel dual wheel floor in the rear. 227mm is the current distance covered side-to-side of the angled corners. Battery Supports allow 400mm+ battery case to attach with support. They are connect to backbone by one QC for stability; four QCs longitudinal provide most of the support. [ id: 51 qty: 1]
- 45 Support Connectors [ 45°Support Connector 45B id: 67 qty: 8]:48.88
- Angled Floor Pieces-Small profiles that give the corners a little angle [ id: 68 qty: 4]
- Profile [ 45 x 45 Heavy id: 69 qty: 180]:6.27
- M8 bolt [ M8 x 16mm id: 72 qty: 2]:0.15
- Threaded [ Thread M12 id: 70 qty: 2]:4.5
- Threaded inserts [ Threaded Insert id: 71 qty: 2]:2.88
- Battery Support Forward-Longitudinal supports for the battery and general rigidity. This one is forward-most [ id: 61 qty: 2]
- Profile [ 45 x 90 Heavy id: 73 qty: 495]:15.16
- QC connectors [ Central Connector Circular id: 75 qty: 5]:3.1
- 10mm hole for QC to connect to backbone [ M10 access hole id: 76 qty: 1]:2.25
- 17mm hole [ M17 access hole id: 74 qty: 5]:11.25
- Battery Support Middle-Longitudinal supports for the battery and general rigidity. This one is sandwiched between the front seat mount and rear seat mount [ id: 62 qty: 2]
- Profile [ 45 x 90 Heavy id: 86 qty: 315]:9.65
- QC connectors [ Central Connector Circular id: 88 qty: 5]:3.1
- 10mm hole for QC to connect to backbone [ M10 access hole id: 89 qty: 1]:2.25
- 17mm hole [ M17 access hole id: 87 qty: 5]:11.25
- Battery Support Rear-Longitudinal supports for the battery and general rigidity. This one is rear-most [ id: 79 qty: 4]
- Profile [ 45 x 90 Heavy id: 80 qty: 270]:8.27
- QC connectors [ Central Connector Circular id: 82 qty: 5]:3.1
- 10mm hole for QC to connect to backbone [ M10 access hole id: 83 qty: 1]:2.25
- 17mm hole [ M17 access hole id: 81 qty: 5]:11.25
- Floor Crossbar Forward and Rear-Profiles that serve as the wheel arch base in the front and rear [ id: 53 qty: 4]
- Profile [ 45 x 90 Heavy id: 54 qty: 540]:16.54
- QC [ Central Connector Circular id: 59 qty: 2]:1.24
- 17mm on backbone side [ M17 access hole id: 57 qty: 2]:4.5
- Thread end for 45 support connector [ Thread M12 id: 56 qty: 1]:2.25
- Floor Crossbar Seat Mount-Profiles that serve as the seat front mount and one for the seat rear mount [ id: 52 qty: 4]
- Profile [ 45 x 90 Heavy id: 55 qty: 540]:16.54
- QC [ Central Connector Circular id: 60 qty: 4]:2.48
- 17mm [ M17 access hole id: 58 qty: 4]:9
- M8 x 14mm [ M8 x 14mm id: 530 qty: 2]:0.29
- Outer Support Forward-Longitudinal supports for general rigidity. This one is forward-most [ id: 64 qty: 2]
- Profile [ 45 x 45 Heavy id: 92 qty: 495]:17.24
- QC connectors [ Central Connector Circular id: 94 qty: 2]:1.24
- 17mm hole [ M17 access hole id: 93 qty: 2]:4.5
- Outer Support Middle-Longitudinal supports for general rigidity. This one is forward-most [ id: 65 qty: 2]
- Profile [ 45 x 90 Heavy id: 98 qty: 315]:9.65
- QC connectors [ Central Connector Circular id: 100 qty: 2]:1.24
- 17mm hole [ M17 access hole id: 99 qty: 2]:4.5
- Outer Support Rear-Longitudinal supports for general rigidity. This one is forward-most [ id: 66 qty: 2]
- Profile [ 45 x 90 Heavy id: 101 qty: 270]:8.27
- QC connectors [ Central Connector Circular id: 103 qty: 2]:1.24
- 17mm hole [ M17 access hole id: 102 qty: 2]:4.5
- Seat Mount-Mounting plate and hardware to mount seat to floor [ id: 536 qty: 2]
- Mounting Plate for seat - 630mm x 630mm [ 1/4" Aluminum Plate id: 520 qty: 1]:0.01
- M10 hole for mounting bolts [ M10 access hole id: 523 qty: 4]:9
- M8 x 16mm [ M8 x 16mm id: 521 qty: 4]:0.62
- TNuts [ T Nut slide in id: 522 qty: 4]:0.4
- Sill-The outermost profile, both sides are the same [ id: 104 qty: 2]
- Profile [ 45 x 90 Heavy id: 109 qty: 1080]:33.08
- M8 bolt [ M8 x 16mm id: 108 qty: 2]:0.31
- Thread end for 45 support connector [ Thread M12 id: 105 qty: 1]:2.25
- Threaded [ Thread M12 id: 106 qty: 2]:4.5
- Threaded inserts [ Threaded Insert id: 107 qty: 2]:2.88
- TNuts [ T Nut slide in id: 531 qty: 2]:0.2
- Front Hoop-From the base that connects to the hood and windshield, legs and four windshield items [ id: 198 qty: 1]
- A Pillar-Sides of windshield [ id: 205 qty: 2]
- Profile [ 45 x 45 Heavy id: 206 qty: 720]:25.07
- QC connector [ Central Connector Circular id: 208 qty: 2]:1.24
- Front Hoop Cross Bar-Under windshield 45 Deg, attaches to front hoop verts and hood supports [ id: 194 qty: 1]
- Profile [ 45 x 90 Heavy id: 195 qty: 1215]:37.21
- QC connector [ Central Connector Circular id: 197 qty: 6]:3.72
- 17mm. Two Middle and each end to attach to windshield [4 total]. Two for attaching Main Steering Column 45 Deg mount [ M17 access hole id: 196 qty: 6]:13.5
- Thread M12 [ Thread M12 id: 528 qty: 2]:4.5
- Front Hoop Vert-Attach front hoop base to the floor [ id: 201 qty: 2]
- Profile [ 45 x 90 Heavy id: 202 qty: 450]:13.78
- QC connector [ Central Connector Circular id: 204 qty: 4]:2.48
- 17mm. [ M17 access hole id: 203 qty: 4]:9
- 17mm. [ M17 access hole id: 207 qty: 2]:4.5
- Windshield Base 45 Deg-Base of windshield [ id: 199 qty: 1]
- Profile [ 45 x 45 x 45 Degree id: 200 qty: 1665]:56.6
- Windshield Top 45 Deg-Top of windshield that connects to roof [ id: 209 qty: 1]
- Profile [ 45 x 45 x 45 Degree id: 210 qty: 1665]:56.6
- Hood-The flat area forward of the front hoop [ id: 175 qty: 1]
- Hood Supports-Mounted with 45mm width left to right and 90mm top to bottom so that a hood compartment for eletronics can be created on the passenger side as well as a mount for the master cylinder and brake pedal on the drivers side [ id: 176 qty: 3]
- Profile [ 45 x 90 Heavy id: 177 qty: 240]:7.35
- QC connector [ Central Connector Circular id: 179 qty: 2]:1.24
- 17mm. Only need QCs on the top to attach to the 45 Degs, but will drill all four for easy use [ M17 access hole id: 178 qty: 4]:9
- Rear Pillars-New main hoop replacement for more room in back and 3 point seat belt attachment. Also two in the back corners before the floor starts to angle [ id: 222 qty: 4]
- Profile [ 45 x 90 Heavy id: 223 qty: 1105]:33.84
- QC connector [ Central Connector Circular id: 225 qty: 4]:2.48
- 17mm. [ M17 access hole id: 224 qty: 4]:9
- Roof-Everything connecting the top of the front hoop to the top of the main hoop rearward [ id: 211 qty: 1]
- Roof 45 Deg Rear Support-Last rearward piece on the roof. This connects to the rear suspension and also allows expansion to a 4 wheeler with supports moved to the sides [ id: 220 qty: 1]
- Profile [ 45 x 45 x 45 Degree id: 221 qty: 1665]:56.6
- Roof Cross supports-Inline with the new main hoop behind the driver's seat, this gives latitudinal support as well as two others inline with the front of the seat [ id: 216 qty: 2]
- Profile [ 45 x 90 Heavy id: 217 qty: 698]:21.38
- 17mm. [ M17 access hole id: 218 qty: 4]:9
- Roof Lengths-The four 4590s spanning from the windshield rearward [ id: 215 qty: 3]
- Profile [ 45 x 90 Heavy id: 212 qty: 770]:23.58
- QC connector [ Central Connector Circular id: 214 qty: 4]:2.48
- 17mm. [ M17 access hole id: 213 qty: 4]:9
- Roof Rear Cross Bar-Allow C Pillar to attach to something since the back corner will be an angle on the floor [ id: 245 qty: 1]
- Profile [ 45 x 45 Heavy id: 246 qty: 1665]:57.98
- QC connector [ Central Connector Circular id: 248 qty: 2]:1.24
- 17mm. [ M17 access hole id: 247 qty: 2]:4.5
- Swing Arm Upper Shock Mount-Old shroud from the base that connects to the floor to the top of the connection to the roof [ id: 226 qty: 1]
- Rear Shock Mount Upper Slope-Attaches to roof 45 Deg [ id: 241 qty: 1]
- Profile [ 45 x 180 6S id: 242 qty: 277]:24.68
- QC connector [ Central Connector Circular id: 244 qty: 4]:2.48
- 17mm. [ M17 access hole id: 243 qty: 4]:9
- Rear Shock Mount Vert-LP attaches to this profile [ id: 237 qty: 1]
- Profile [ 45 x 180 6S id: 238 qty: 360]:32.08
- QC connector [ Central Connector Circular id: 240 qty: 4]:2.48
- 17mm. [ M17 access hole id: 239 qty: 4]:9
- Shroud 45 Deg-Three profiles. 1. Connect to 4590L downward and 45-180 rearward. 2. Connect to 45-180 downward and 45-180S upward. 3. Connect to 45-180S downward and final 45-180S upward toward roof [ id: 231 qty: 3]
- Profile [ 45 x 45 x 45 Degree id: 232 qty: 180]:6.12
- Shroud Base-4590L that connects to the floor. Also used for mounting the rear controller [ id: 230 qty: 1]
- Profile [ 45 x 90 x 90 id: 227 qty: 180]:19.68
- QC connectors [ Central Connector Circular id: 229 qty: 7]:4.34
- 17mm hole - Seven total. Four total into the Control Arm Base Mount: two in each longitudinal slot. Three to secure the 45 Deg to the top [ M17 access hole id: 228 qty: 7]:15.75
- Shroud Upper Shock Mount-The profile to which the brackets mount that secure the rear shock[s] [ id: 233 qty: 1]
- Profile [ 45 x 180 Heavy id: 234 qty: 360]:68.76
- QC connector [ Central Connector Circular id: 236 qty: 4]:2.48
- 17mm. [ M17 access hole id: 235 qty: 4]:9
- Throttle Mount-Small profile and a bracket, very simple [ id: 378 qty: 1]
- 2 Hole bracket [ 45 Series Corner Bracket - 2 Holes id: 384 qty: 1]:4.42
- Profile [ 45 x 45 Heavy id: 379 qty: 180]:6.27
- QC connector [ Central Connector Circular id: 381 qty: 2]:1.24
- 17mm. [ M17 access hole id: 380 qty: 2]:4.5
- M8 lock nuts [ M8 Lock Nut id: 385 qty: 1]:0.11
- M8 x 16mm bolt [ M8 x 16mm id: 382 qty: 3]:0.46
- TNut [ T Nut slide in id: 383 qty: 2]:0.2
- Double Wishbone Suspension-For front suspension or rear suspension on 4 wheeler. Both control arms from the swing arm bolt to the uprights. Brackets are part of the chassis [ id: 249 qty: 2]
- Coil Over Shock-Includes bolts spacers nuts and the shock itself. Brackets are part of the chassis or suspension item to which the brackets mount [ id: 278 qty: 1]
- USM, double wishbone. Just one bracket, other side is an L Plate [ 45 Series Corner Bracket - 2 Holes id: 279 qty: 1]:4.42
- LSM, double wishbone [ 45 Series Corner Bracket - 2 Holes id: 537 qty: 2]:8.84
- Coil Over Shock [ Coil over shock id: 287 qty: 1]:43.03
- Mounting plate for USM, forward side [ Corner Plate 135mm x 135mm angled id: 455 qty: 1]:11.73
- M10 hole [ M10 access hole id: 280 qty: 4]:9
- M10 Lock nut [ M10 Lock Nut id: 290 qty: 2]:0.19
- Spacer. Keeps the lower shock in the right place [ M10 Spacer id: 286 qty: 1]:2
- USM bolt [ M10 x 45mm id: 288 qty: 1]:1.64
- LSM bolt [ M10 x 55mm id: 289 qty: 1]:1.4
- M8 Flat head bolt [ M8 flat head x 14mm id: 283 qty: 2]:0.24
- M8 bolt [ M8 x 25mm id: 284 qty: 2]:0.54
- Ream M10 hole [ Ream access hole id: 281 qty: 2]:4.5
- TNut [ T Nut slide in id: 285 qty: 4]:0.4
- Trim ends [ Trim Bracket Ends id: 282 qty: 4]:9
- Coil Over Shock Rear Swing Arm-Includes bolts spacers nuts and the shock itself. Brackets are part of the chassis or suspension item to which the brackets mount [ id: 538 qty: 1]
- Lower Control Arm Parent-This is two pieces. 1. The main control arm, BOM like UCA. 2. Swing Arm Bolt Adapter. Required since the swing arm bolt bushing flange is 2.5mmm thick, [ id: 263 qty: 1]
- Lower Control Arm Adapter-Allows 180mm wide control arm to attach to LCA plates, given 2.5mm thick flanges on the bushings [ id: 271 qty: 1]
- Profile [ 45 x 45 Heavy id: 272 qty: 175]:6.09
- Swing Arm Bolt [ LCA Swing Arm Bolt id: 273 qty: 1]:7.55
- Swing Arm Bolt Lock Nut [ M10 Lock Nut id: 274 qty: 1]:0.1
- Swing Arm Bolt Bushing [ M10 Swing Arm Bushing id: 275 qty: 2]:1.9
- Lower Control Arm Main-Everything from the swing arm bolt to the ball joint on the LCA [ id: 264 qty: 1]
- Profile [ 45 x 180 Heavy id: 265 qty: 315]:60.17
- Ball Joint Plate [ Bolt on Ball Joint Plate id: 266 qty: 1]:25.25
- QC connector [ Central Connector Circular id: 277 qty: 2]:1.24
- M10 fail-safe holes [ M10 access hole id: 268 qty: 6]:13.5
- 17mm. [ M17 access hole id: 276 qty: 2]:4.5
- M8 bolt [ M8 x 25mm id: 269 qty: 6]:1.62
- M9 access holes [ M9 access hole id: 267 qty: 6]:13.5
- TNut [ T Nut slide in id: 270 qty: 6]:0.59
- Upper Control Arm-Everything from the swing arm bolt to the ball joint on the UCA [ id: 250 qty: 1]
- Profile [ 45 x 90 Heavy id: 251 qty: 270]:8.27
- Bolt On Ball Joint [ Bolt on Ball Joint id: 262 qty: 1]:19.5
- Ball Joint Plate [ Bolt on Ball Joint Plate id: 254 qty: 1]:25.25
- Swing Arm Bolt Hole [ M10 access hole id: 252 qty: 1]:2.25
- M10 fail-safe holes [ M10 access hole id: 256 qty: 6]:13.5
- Swing Arm Bolt Lock Nut [ M10 Lock Nut id: 260 qty: 1]:0.1
- Swing Arm Bolt Bushing [ M10 Swing Arm Bushing id: 261 qty: 2]:1.9
- Bushing hole [ M12 access hole id: 253 qty: 2]:4.5
- M8 bolt [ M8 x 25mm id: 257 qty: 6]:1.62
- M9 access holes [ M9 access hole id: 255 qty: 6]:13.5
- TNut [ T Nut slide in id: 258 qty: 6]:0.59
- Swing Arm Bolt [ UCA Swing Arm Bolt id: 259 qty: 1]:2.33
- Mustang 2 -Upper Shock mount system like what we are using with Prototype. This is the 45 degree angle (attached to the UCA mount), 180mm section that the shock mounts to, then 45 degree to a crossbar. The drawback is that the coil over is on an angle instead of vertical like wheel arch mounting [ id: 137 qty: 1]
- Mustang 2 45 Degs-45 Deg connectors from upper control arm mount to upper shock mount [x2] and from upper shock mount to crossbar [x2] [ id: 143 qty: 4]
- Profile [ 45 x 45 x 45 Degree id: 157 qty: 180]:6.12
- Mustang 2 Crossbar Forward-Connects the left side Mustang 2 upper shock mount with the right side [ id: 147 qty: 1]
- Profile [ 45 x 90 Heavy id: 154 qty: 630]:19.29
- QC connector [ Central Connector Circular id: 156 qty: 7]:4.34
- 17mm. 4 at the ends for connection to 45 Deg upper shock mounts and 3 on the front side to attach to 45Deg hood deflector [ M17 access hole id: 155 qty: 7]:15.75
- Mustang 2 Crossbar Rearward-Connects the left side Mustang 2 upper shock mount with the right side. 4590 is much cheaper to buy 2 than one 45180,also can get these from Mesier [ id: 153 qty: 1]
- Profile [ 45 x 90 Heavy id: 148 qty: 630]:19.29
- QC connector [ Central Connector Circular id: 150 qty: 4]:2.48
- 17mm. 4 at the ends for connection to 45 Deg upper shock mounts [ M17 access hole id: 149 qty: 4]:9
- Mustang 2 Upper Shock Mount -Angled mount to which the upper shock mount attaches [ id: 144 qty: 2]
- Profile [ 45 x 180 Heavy id: 142 qty: 180]:34.38
- QC connector [ Central Connector Circular id: 140 qty: 4]:2.48
- 17mm - two standard holes for connection to upper control arm 45Deg, two on the sides for connection to cross bar 45Deg [ M17 access hole id: 138 qty: 4]:9
- WAGO - single port [ 2 Port WAGO id: 387 qty: 5]:2.41
- Cable Blocks for throttle and rear 8 wire [ Cable Mounting Block id: 373 qty: 3]:0.39
- M9 holes. [ M9 access hole id: 388 qty: 4]:9
- Single Axle Power Train-BLDC, Upright, Controller, throttle and all wiring. Braker, resistor, etc is part of 72V System [ id: 346 qty: 3]
- Direct Wheel Drive-All items directly related to one BLDC power up to the controller [ id: 535 qty: 1]
- Shaft Washer [ 1.25in BLDC Shaft Washer id: 358 qty: 1]:2.4
- WAGO - single port [ 2 Port WAGO id: 366 qty: 5]:2.41
- WAGO - five port for all for expansion [ 5 Port WAGO id: 367 qty: 8]:4.95
- BLDC motor [ 5kW BLDC Hub Motor - Single Axle id: 357 qty: 1]:436.25
- Brake rotor. Must be part of this due to the order of creating the modules [ Brake rotor id: 354 qty: 1]:23.42
- Cable Block for 3 phase [ Cable Mounting Block id: 364 qty: 2]:0.26
- Bluetooth Module [ Controller Bluetooth adapter id: 361 qty: 1]:19.99
- 3 Phase Wire Guide [ Corner Plate 135mm x 135mm angled id: 362 qty: 1]:11.73
- 17" Rims [ Drag DR-33 Rim 17 X7.5 4-100.00/108.00 42 id: 389 qty: 1]:117
- Controller [ FarDriver 72450 id: 359 qty: 1]:140.5
- Tire [ Goodyear Wrangler Territory RT 235/65r17 id: 390 qty: 1]:170.85
- Zip tie holes [ M6 access hole id: 363 qty: 2]:4.5
- M8 Flat head bolt [ M8 flat head x 14mm id: 355 qty: 3]:0.36
- M8 x 35mm bolt [ M8 x 35mm id: 370 qty: 2]:0.62
- M9 holes. [ M9 access hole id: 368 qty: 4]:9
- Controller Mount Bore hole [ M9 access hole id: 369 qty: 4]:9
- TNut [ T Nut slide in id: 371 qty: 2]:0.2
- Upright -All components needed to create the finished upright. Fabrication to the aluminum block itself is contained in the fabrication line item. [ id: 345 qty: 1]
- 2 Hole bracket [ 45 Series Corner Bracket - 2 Holes id: 348 qty: 3]:13.26
- 4 hole Bracket [ 45 Series Corner Bracket - 4 Holes id: 347 qty: 2]:16.6
- LCA pivot plate. [ LCA Pivot Plate id: 349 qty: 1]:5
- M8 x 30mm bolt [ M8 flat head x 30mm id: 350 qty: 10]:1.69
- M8 lock nuts [ M8 Lock Nut id: 353 qty: 6]:0.64
- Valve Stem [ Valve Stem Cap id: 392 qty: 1]:1.5
- Switch Bank-Replace current bracketed switches for motors and reverse. The top is existing Dash Shelf with one more 2080 to reach current location. Sides are 2080 x 240mm [i.e. three 2080 back to back]. Bottom will be paneling: 240mm x 270mm]. Face is paneling, like Gauge Display Bank: 270mm W x 80mm H [ id: 374 qty: 1]
- 2 Port WAGO - three 72V toggle switches x 3 [ 2 Port WAGO id: 481 qty: 9]:4.34
- Profile. Dash shelving [1m x 3]. Sides are 2080 x 240mm [x2]. Bottom will be paneling: 240mm x 270mm]. Face is paneling, like Gauge Display Bank: 270mm W x 80mm H [ 2080 Black id: 430 qty: 3480]:69.6
- Female Slot connectors - Toggle switches [ Female slot connector id: 416 qty: 9]:0.54
- HDPE. Back 270mm x 80mm. Face: 270mm x 80. Bottom: 270mm x 240mm. Total Sheet needed: 270mm x 400mm, Less than 2' x 2' [ HDPE Sheet 4' x 8' x .25" thick id: 431 qty: 0.25]:16.56
- Inline Fuse +72V toggle switch [ In line pigtail + fuse id: 493 qty: 3]:2.25
- Push button switches: reverse, Cruise and extra [ M12 push button threaded switch id: 376 qty: 3]:7.77
- Prep wire for toggle switches [ Strip, Crimp, insulate wire end id: 417 qty: 9]:5.22
- Prep wire for 18/8 rear controller run [ Strip, Crimp, insulate wire end id: 482 qty: 8]:4.64
- Toggle switches [ Toggle switch id: 375 qty: 3]:9.99
- Volt Meter - 72V [ Volt meter id: 491 qty: 3]:7.99
- Throttle [ Throttle id: 372 qty: 1]:18.55
- TPMS and valve stems [ Tire Pressure Monitoring System with internal sensors id: 391 qty: 1]:33.91
- Forward Controller Junction Box. One big one for both front controllers. [ Waterproof Container: Large id: 365 qty: 1]:5.2
- Rear Controller Junction Box. Easy to use for expansion to four wheels [ Waterproof Container: Large id: 386 qty: 1]:5.2
- Rear Swing Arm Cross Bar-Allow leg to securely attach to one side and adapter to the other. [ id: 297 qty: 1]
- Profile [ 45 x 180 Heavy id: 298 qty: 360]:68.76
- QC connector [ Central Connector Circular id: 300 qty: 2]:1.24
- M10 access hole [ M10 access hole id: 307 qty: 6]:13.5
- 17mm. [ M17 access hole id: 299 qty: 3]:6.75
- Rear Swing Arm Leg-Give support to aluminum block bar [ id: 301 qty: 1]
- 2 Hole bracket for brake caliper mount [ 45 Series Corner Bracket - 2 Holes id: 356 qty: 2]:8.84
- Profile [ 45 x 180 Heavy id: 302 qty: 405]:77.36
- QC connector [ Central Connector Circular id: 304 qty: 2]:1.24
- 17mm. [ M17 access hole id: 303 qty: 3]:6.75
- M8 Bolt [ M8 x 25mm id: 306 qty: 6]:1.62
- Rear Swing Arm BLDC Bar [ Rear Swing Arm bar id: 305 qty: 1]:90.81
- Rear Swing Arm Mounting Adapter-Allows cross bar to attach to brackets, given 2.5mm thick flanges on the bushings and 7mm thickness/offset of brackets [ id: 292 qty: 1]
- Profile [ 45 x 45 Heavy id: 293 qty: 161]:5.61
- Swing Arm Bolt [ LCA Swing Arm Bolt id: 294 qty: 1]:7.55
- Swing Arm Bolt Lock Nut [ M10 Lock Nut id: 295 qty: 1]:0.1
- Swing Arm Bolt Bushing [ M10 Swing Arm Bushing id: 296 qty: 2]:1.9
- [ Flip Windshield id: 534 qty: 1]:379.99
- M8 x 16mm [ M8 x 16mm id: 525 qty: 2]:0.31
- Rearview Golf Cart Mirror [ Rear view mirror id: 524 qty: 1]:16.98
- Seat [ Seat - 551.mm wide id: 519 qty: 2]:219.99
- Seat Belts [ Seat Belt id: 529 qty: 2]:35.15
- Side View Mirror [ Side view mirrors id: 527 qty: 2]:13.99
- TNuts [ T Nut slide in id: 526 qty: 2]:0.2
- DD Rod. 3/4in, 240mm [ 3/4" DD rod id: 317 qty: 1]:0.05
- U Joint. 1in DD to 3/4in DD [ 3/4" to 1" DD U Joint id: 319 qty: 1]:16.99
- 3/8in lock nut [ 3/8in lock nut id: 344 qty: 4]:0.46
- 4 hole bracket [ 40 Series Corner Bracket - 4 Holes id: 309 qty: 1]:7.2
- Mounting bracket. Both will mount to Brake Pedal Support forward tslot [ 45 Series Corner Bracket - 2 Holes id: 325 qty: 2]:8.84
- Profile [ 45 x 45 x 45 Degree id: 324 qty: 180]:6.12
- U Joint. 36 Spline to 3/4in DD [ 5/8" 36 spline to 3/4" DD U Joint id: 316 qty: 1]:19.99
- 5/8" washer [ 5/8" Heim Washer id: 341 qty: 8]:4.09
- Left hand Heims [ Left Hand Heim id: 339 qty: 2]:15.9
- Left Tie Rod [ Left Tie Rod: 5" id: 337 qty: 1]:12.52
- Spacer. Needed between bottom of steering rack and tslot of profile to which it is attaching [ M10 Spacer id: 315 qty: 2]:4
- M8 x 16mm bolt [ M8 x 16mm id: 312 qty: 1]:0.15
- M8 x 16mm bolt [ M8 x 16mm id: 326 qty: 4]:0.62
- M8 x 50mm bolt [ M8 x 50mm id: 313 qty: 2]:0.81
- M9 dimple in DD rod for steering rack U Joint and upper steering column U Joint, 2 on each [ M9 dimple id: 311 qty: 4]:9
- Main Steering Column Mount, lower-There are two 2in mounts for the upper steering column. This is the one nearest the U Joint [ id: 320 qty: 1]
- M8 socket head [ M8 socket head id: 322 qty: 2]:1.56
- 2in mounting bracket [ Steering column bracket id: 321 qty: 1]:9.5
- TNut [ T Nut slide in id: 323 qty: 2]:0.2
- Main Steering Column Mount, upper-There are two 2in mounts for the upper steering column. This is the one nearest the steering wheel [ id: 328 qty: 1]
- Profile [ 45 x 45 x 45 Degree id: 332 qty: 180]:6.12
- End Caps [ End Cap 45mm x 45 Degree Radius id: 335 qty: 2]:4.96
- M8 socket head [ M8 socket head id: 330 qty: 2]:1.56
- 2in mounting bracket [ Steering column bracket id: 329 qty: 1]:9.5
- TNut [ T Nut slide in id: 331 qty: 2]:0.2
- Right hand Heims [ Right Hand Heim id: 340 qty: 2]:17.74
- Right Tie Rod [ Right Tie Rod: 29" id: 338 qty: 1]:22.56
- Off the shelf column [ Steering column id: 318 qty: 1]:152
- Steering Knuckle-45Deg and 4590 profiles that attach to the upright along with the fabrication and bushings [ id: 408 qty: 1]
- Profile [ 45 x 45 x 45 Degree id: 409 qty: 180]:6.12
- Profile [ 45 x 90 Heavy id: 410 qty: 180]:5.51
- QC connector [ Central Connector Circular id: 412 qty: 3]:1.86
- M10 access holes [ M10 access hole id: 413 qty: 3]:6.75
- Bushing [ M10 Swing Arm Bushing id: 415 qty: 2]:1.9
- Bushing hole [ M12 access hole id: 414 qty: 2]:4.5
- 17mm [ M17 access hole id: 411 qty: 3]:6.75
- M8 x 60mm bolt [ M8 flat head x 60mm id: 351 qty: 3]:1.57
- TNut for steering knuckle [ T Nut slide in id: 352 qty: 3]:0.3
- Knuckle side tie rod bolt [ Steering Knuckle 3/8in bolt x 4.5in id: 343 qty: 2]:1.2
- Steering Rack [ Steering Rack id: 308 qty: 1]:169.95
- Rack side tie rod bolt [ Steering Rack 3/8in bolt x 2in id: 342 qty: 2]:1.27
- Steering Wheel [ Steering Wheel id: 336 qty: 1]:124.99
- TNut [ T Nut slide in id: 314 qty: 3]:0.3
- TNut [ T Nut slide in id: 327 qty: 4]:0.4
- Trim bracket to fit in front of spline [ Trim Bracket Ends id: 310 qty: 1]:2.25
Module Data